XeVision HID Xenon & LED lighting technology for aerospace and industry

e-mail
toll-free 800-366-4415

XeVision HID & LED lighting systems for aerospace & industrial applications

HID Xenon Technology

Landing and taxi lights

XeVision proprietary

HID pulsing system

HID Xenon Mobile Technology

XeVision HID Xenon mobile utility and work lights

utility lights / search lights

LED Technology

The Aviator's Choice

Pulsing System

members login

™XeVision HID Xenon Pulsing system ™XePulse & ™XeStrike

Actual pulsing on a Glasar I RG using our XePulse pulsing module and our new XeStrike ballast controlling two of our 35 watt XV-23 HID Xenon lamps one in each wing tip. Pulsing time is 1 Hz (60 pulses per minute on each channel).

Introduction

Our new (Patent pending) HID Xenon capable pulsing system ™XePulse (XV-PCM1) is specially designed to safely and reliably drive our new proprietary electronic ballast ™XeStrike XV1A. If used with other brand ballasts, we cannot grant any warranty. Commonly, standard ballasts currently on the market will not maintain reliable pulsing and might prematurely burn out.

The complete system for alternating pulsing consists of:
- one ™XePulse (Patent pending) pulsing module
- two ™XeStrike XV1A ballasts
- two landing/taxi lights
- one 3 position toggle switch (not included)
- wiring & harness

Example of a complete pulsing system with ™XePulse, ™XeStrike, and two HID lights

Partial systems and the pulsing modules are available as well, please call.

™XePulse Pulsing Module characteristics

Alternating or simultaneous pulsing rate ('wig-wag' rate) is preset to 1Hz (60 pulses per minute on each channel).

™XePulse is capable of driving various HID loads as shown below
14 volt aircraft:
2 x 35 watt HID system per channel or
1 x 50 watt HID system maximum per channel.
28 volt aircraft:
2 x 50 watt HID system per channel maximum.

™XePulse can be used with traditional incandescent lamps also.
14 volt systems 125 watts maximum per channel,
28 volt systems 250 watts maximum per channel.

If both channels are connected, pulsing is always alternating, otherwise simultaneous or alternating pulsing can be selected.
A low current three position toggle switch is used to select between
off - continuous on - pulsing, no relay is required.

The pulsing unit is best placed in a dry environment, one possible location is behind the instrument panel.

XeVision XePulse XV-PCM1 HID pulsing module
pulsing module ™XePulse XV-PCM1

™XePulse Pulsing Module specifications

XePulse Controller	XV-PCM-12	XV-PCM-24
Normal operating input voltage range	10 - 18 VDC	18 - 32 VDC
Terminal # 1 Pulsing is activated when connect with terminal # 3. Pulsing frequency is 1 HZ	Pulsing On / Off	Pulsing On / Off
#2 Always ON when connect to Pin # 3	ON / ON	On / On
# 3 Regulated + 12 VDC	12.0 V DC	12.0 V DC
# 4 System Ground	GND	GND
# 5 Left Channel power out put	10 V~ 18 V	18V ~ 32 V
# 6 System Ground	GND	GND
# 7 Right Channel Power Output	10 V ~ 18 V	18 V ~ 32 V
# 8 System Power Input	10 V ~ 18 V	18 V ~ 32 V
Dimensions housing (fiber reinforced plastic)	100 x 61 x 30 mm	100 x 61 x 30 mm
Weight pulsing module	160 gr	160 gr

top

For more information call +1 (801) 622-7000 or contact us by e-mail

For ordering call toll free 1-800-366-4415

XeVision, 4245 Airport Road, Ogden, UT 84405, USA - phone: +1 (801) 622-7000 fax: +1 (801) 622-7277