™XeStrike proprietary ballasts
Features for all XeStrike ballasts
Full Al case with Si seal or Si O-ring, complies with IP 67
Low EMI.
Uses resonant zero voltage switching technology.
Hot restrike
Output capable of driving up to 5 m shielded D1 cable
Dimmable once the voltage drops below 8.0 (12 V system) or 18 volts (24 V system).
High efficiency under wide range of operating conditions.
Drives D1S bulb as well as D2S bulb with our external ignitor
35 or 50 watts systems (VPM see below)
Active reverse input polarity protection
Open and short output protection
Input over-voltage switches off with automatic restart
Input under-voltage shut down, self locked
Fast restart cycles
Smooth lamp current curve
Smart warm up control
CR*) technology (Continuous Restrike technology).
Fully dust & waterproof design to IP 67.
XV1A special features
Wide range input voltage (8 to 32 VDC)
Drives D1S bulb as well as D2S bulb with our external ignitor
XV3A special features
Thin, lightweight ballast
With and without mounting tabs
VPM**) technology
DC version available on request.
XV4A special features
Super thin, lightweight ballast
With and without mounting tabs
VPM**) technology
DC version available on request.
XV2DC special features
DC output
35 watt only
*) CR Technology: Continuous Restrike technology
**) VPM: Variable Power Mode for dual power setting
VPM explained:
Variable power mode means that the output power can be variably selected for two presets, for example 50 watt and 38 watt for dimming purposes to conserve battery power.
|
|
|
Parameter
|
XV1A-35
|
XV1A-50
|
|
Normal operating input voltage range
|
8V - 32V
|
8V - 32V
|
|
Extended operating input voltage range
|
6V - 34V
|
6V - 34V
|
|
Starting input voltage range
|
7V - 32V
|
7V - 32V
|
|
Nominal output power
|
35W ± 2 W
|
50W ± 2 W
|
|
Maximum run up output power
|
80W
|
100W
|
|
Max. steady state lamp current
|
3.2 A
|
4.6 A
|
|
Maximum inrush current at 13.5 V
|
6 A
|
8 A
|
|
Max inrush current @ 10 V low power level
|
8 A
|
10 A
|
|
Efficiency of D1S and ballast at nominal supply
|
83 %
|
83 %
|
|
Ballast unit efficiency
|
83 %
|
83 %
|
|
Output steady state frequency
|
400 +/- 20 Hz
|
400 +/- 20 Hz
|
|
Temperature range
|
-40 to +85 °C
|
-40 to +85 °C
|
| Water/dust environment |
meets IP 67
|
meets IP 67
|
| Weight (no wires/connectors, w tabs) |
360 gr
|
360 gr
|
| Dimensions (without tabs) |
length: 92 mm
width: 78 mm
height: 32 mm
|
length: 92 mm
width: 78 mm
height: 32 mm
|
|
Parameter
|
XV3A-35
|
X3A-50
|
|
Normal operating input voltage range
|
8-18 / 18-32 VDC
|
8-18 / 18-32 VDC
|
|
Start-up / turn-off voltage
|
9.5 / < 6 VDC
|
9.5 / < 6 VDC
|
|
Starting input voltage range
|
7V - 32V
|
7V - 32V
|
|
Nominal output power
|
35W ± 2 W
|
50W ± 2 W
|
|
Maximum run up output power
|
80W
|
100W
|
|
Max. steady state lamp current
|
3.2 / 1.6 A
|
4.6 / 2.3 A
|
|
Maximum inrush current at 13.5 V
|
6 / 3 A
|
8 / 4 A
|
|
Max inrush current @ 10 VDC low power level
|
8 / 4 A
|
10 / 5 A
|
|
Efficiency of D1S and ballast at nominal supply voltage
|
> 85 % / > 90 %
|
> 85 % / > 90 %
|
|
Steady state output voltage
|
60 to 110 VAC
|
60 to 110 VAC
|
| Triggered DPM |
from 10 to 18 VDC
|
-
|
|
Output steady state frequency
|
400 +/- 20 Hz
|
400 +/- 20 Hz
|
|
Temperature range
|
-40 to +85 °C
|
-40 to +85 °C
|
| Water/dust environment |
meets IP 67
|
meets IP 67
|
| Weight (no wires/connectors, w tabs) |
210 gr
|
210 gr
|
| Dimensions (without tabs) |
length: 83 mm
width: 71 mm
height: 20 mm
|
length: 83 mm
width: 71 mm
height: 20 mm
|
|
Parameter
|
XV4A-35
|
XV4A-50
|
|
Normal operating input voltage range
|
8-18 / 18-32 VDC
|
8-18 / 18-32 VDC
|
|
Start-up / turn-off voltage
|
9.5 / < 6 VDC
|
9.5 / < 6 VDC
|
|
Starting input voltage range
|
7V - 32V
|
7V - 32V
|
|
Nominal output power
|
35W ± 2 W
|
50W ± 2 W
|
|
Maximum run up output power
|
80W
|
100W
|
|
Max. steady state lamp current
|
3.2 / 1.6 A
|
4.6 / 2.3 A
|
|
Maximum inrush current at 13.5 V
|
6 / 3 A
|
8 / 4 A
|
|
Max inrush current @ 10 V low power level
|
8 / 4 A
|
10 / 5 A
|
|
Efficiency of D1S and ballast at nominal supply
|
> 85 % / > 90 %
|
> 85 % / > 90 %
|
|
Steady state output voltage
|
60 to 110 VAC
|
60 to 110 VAC
|
| Triggered DPM |
from 10 to 18 VDC
|
-
|
|
Output steady state frequency
|
400 +/- 20 Hz
|
400 +/- 20 Hz
|
|
Temperature range
|
-40 to +85 °C
|
-40 to +85 °C
|
| Water/dust environment |
meets IP 67
|
meets IP 67
|
| Weight (no wires/connectors, w tabs) |
170 gr
|
170 gr
|
| Dimensions (without tabs) |
length: <84 mm
width: <74 mm
height: <16 mm
|
length: <84 mm
width: <74 mm
height: <16 mm
|
|
Parameter
|
XV2DC
|
|
Normal operating input voltage range
|
8V - 32V
|
|
Start-up / turn-off voltage
|
9.5 / < 6 VDC
|
|
Starting input voltage range
|
7V - 32V
|
|
Nominal output power
|
35W ± 2 W
|
|
Maximum run up output power
|
80W
|
|
Max. steady state lamp current
|
3.2 A
|
|
Maximum inrush current at 13.5 V
|
6 A
|
|
Max inrush current @ 10 V low power level
|
8 A
|
|
Efficiency of D1S and ballast at nominal supply
|
83 %
|
|
Ballast unit efficiency
|
83 %
|
|
Output steady state frequency
|
400 +/- 20 Hz
|
|
Temperature range
|
-40 to +85 °C
|
| Weight (including cable and connector) |
495 gr
|
| Dimensions (without tabs) |
length: 88 mm
width: 77 mm
height: 35 mm
|
|
|
|
|
™XeSparQ D2 to D1 conversion module
The XeSparQ module (adapter) is designed to convert any D2 bulb on the market to a D1 bulb with integrated igniter.
The specifications on the right side show the module with two of a variety of bulbs.
The adapter dimensions along with the overall dimensions are shown in the 3-view drawing. Dimensions are metric (mm).
We offer a warranty of five years on the XeSparQ module
and full manufacturer warranty on converted D2 bulbs
|
|
|
PARAMETER
|
™XeSparQ D1 50 Watt
|
™XeSparQ D1 35 Watt
|
|
Application
|
For Aerospace and Industry
|
For Aerospace and Industry
|
|
Light Source Power
|
50 +/- 3 W
|
35 +/- 3 W
|
|
Voltage
|
85 +/- 17 VAC
|
85 +/- 17 VAC
|
|
Luminance flux after warm-up
|
5300 lm +/- 450lm
|
3200 lm +/-450lm
|
|
Lamp Life
|
B3 = 1050 hrs
Tc = 2100 hrs
|
B3 =1500 hrs
Tc = 2500 hrs
|
|
Color Temperature
|
4150° K
|
4250° K
|
|
Distance between electrodes
|
4.2 +/- 0.045 mm
|
4.2 +/- 0.045mm
|
|
Light Center Length (L.C.L)
|
27.1 +/- 0.15 mm
|
27.1 +/- 0.15 mm
|
|
Maximum socket temperature
|
250°C
|
210°C
|
|
Burning Position
|
Horizontal +/- 10 °
|
Horizontal +/- 10°
|
| Weight |
54 gr
|
54 gr
|
| Dimensions |
43.9 x 43.9 x 24.4
|
43.9 x 43.9 x 24.4
|
| Connector type |
AMP Quadro lock
|
AMP Quadro lock
|
|
|
|
|
™XePulse Pulsing Module
The XePulse Controller is designed for pulsing aircraft landing and/or taxi lights.
|
|
|
XePulse Controller
|
XV-PCM-12
|
XV-PCM-24
|
|
Normal operating input voltage range
|
10 - 18 VDC
|
18 - 32 VDC
|
|
Terminal
# 1 Pulsing is activated when connect to
terminal # 3. Pulsing frequency is 1 HZ
|
Pulsing
On / Off
|
Pulsing
On / Off
|
|
# 2 Always ON when connect to Pin # 3
|
ON / ON
|
On / On
|
|
# 3 Regulated + 12 VDC
|
12.0 V DC
|
12.0 VDC
|
|
# 4 System Ground
|
GND
|
GND
|
|
# 5 Left Channel power out put
|
10 V~ 18 V
|
18V ~ 32 V
|
|
# 6 System Ground
|
GND
|
GND
|
|
# 7 Right Channel Power Output
|
10 V ~ 18 V
|
18 V ~ 32 V
|
|
# 8 System Power Input
|
10 V ~ 18 V
|
18 V ~ 32 V
|
| Dimensions housing (fiber reinforced plastic) |
100 x 61 x 30 mm
|
100 x 61 x 30 mm
|
| Weight pulsing module |
160 gr
|
160 gr
|
|
|
|
|
D1S bulb
We offer only first grade D1S bulbs from leading brand names.
We offer full manufacturer warranty.
See bulb dimensions and 3-VIEW drawing above (section XeSparQ, right side). Dimensions are metric (mm).
|
|
|
PARAMETER
|
boosted 50 Watt
|
35 Watt
|
|
Application
|
For Aerospace and Industry
|
For Aerospace and Industry
|
|
Light Source Power
|
50 +/- 3 W
|
35 +/- 3 W
|
|
Voltage
|
85 +/- 17 VAC
|
85 +/- 17 VAC
|
| Ignition voltage |
1000 V
|
1000 V
|
|
Luminance after warm-up
|
5300 lm +/- 450lm
|
3200 lm +/-450lm
|
|
Lamp Life
|
B3 = 1050 hrs
Tc = 2000 hrs
|
B3 =1500 hrs
Tc = 2500 hrs
|
|
Color Temperature
|
4250° K
|
4300° K
|
|
Distance between electrodes
|
4.2 +/- 0.045 mm
|
4.2 +/- 0.045mm
|
|
Light Center Length (L.C.L)
|
27.1 +/- 0.15 mm
|
27.1 +/- 0.15 mm
|
|
Maximum socket temperature
|
210°C
|
210°C
|
|
Burning Position
|
Horizontal +/- 10 °
|
Horizontal +/- 10°
|
|
|
|
|
™XeVision double shielded Teflon® cables
Our new proprietary double shielded cables are now standard for all XeVision HID Xenon lighting systems. We produce the cables in custom length of 1, 2, 4, and 6 feet.
These shielded Teflon® cables are used between the ballast and the lamp and are pre-assembled with shielded connectors and are a major factor to suppress RMI/EMI.
On both ends there is a MQS connector which is shielded in contact with the ballast and the lamp, a major factor to suppress RMI/EMI.
 click for larger image
Our XeVision proprietary cable is double shielded including the connectors It is a Teflon® insulated cable with a Tinned copper braid shield and a Aluminum foil shield. The wires are Tinned copper strand with Teflon® insulation.
ELECTRICAL CHARACTERISTICS:
Nom. Inductance .124 µH/ft Nom. Capacitance Conductor to Conductor @ 1 KHz 33 pF/ft Nom. Cap. Cond. to Other Cond. & Shield @ 1 KHz 60 pF/ft Nom. Conductor DC Resistance @ 20 Deg. C 5.8 Ohms/1000 ft Nominal Outer Shield DC Resistance @ 20 Deg. C 3.9 Ohms/1000 ft Max. Operating Voltage - UL 300 V RMS Max. Recommended Current 5.4 Amps per conductor @ 25°C
COMPLIANCES:
NEC/(UL) Specification, CMP CEC/C(UL) Specification CMP EU CE Mark, EU RoHS Compliant, EU RoHS
|
|
PHYSICAL CHARACTERISTICS DATA
|
|
|
|
Conductor:
|
|
Number of Conductors
|
3
|
|
Total Number of Conductors
|
3
|
|
AWG
|
18
|
|
Stranding
|
19x30
|
|
Conductor Material
|
TC - Tinned Copper
|
|
|
|
Insulation:
|
|
|
Insulation Material
|
FEP - Fluorinated Ethylene Propylene
|
|
Nom. Insulation Wall Thickness
|
.007 in.
|
|
|
| Overall cabling: |
|
| color code lead 1 |
black |
| color code lead 2 |
white |
| color code lead 3 |
red |
|
|
| Outer shield material: |
|
| inner layer |
Al foil with polyester, 100% shield |
| outer layer |
Tinned Copper braid, 85% shield |
|
| Outer jacket material: |
|
| insulation layer |
blue FEP (Fluorianted Ethylene Propylene) |
|
|
| Mechanical: |
|
| overall diameter |
0.18 in. |
| min. bend radius |
1.87 in. |
| operating temperature range |
- 70ºC to 200ºC |
| flame test |
UL Flame Test NFPA 262 C(UL) Flame Test FT6
|
|
